Toggle Nav
Search
Geavanceerd zoeken
NL EN

Bel gerust! 073 - 624 1111

  • Vergelijken
NL
Cart
Mijn offerte

ICS Analog Interface Module 2361A

Levertijd:
3~4 weken
SKU
2361A

RS-232/RS-485 to Analog Interface

● Provides four floating 16-bit analog outputs with 750 VDC isolation. Controls analog devices without ground loops.
● Four differential analog inputs with programmable ranges. Scalable inputs for reading voltage sources, current shunts, sensors etc.
● User setable scale factors for all analaog singals. Matches 2361A commands and data to real values.
● High current drivers can operate external relays etc. Digital control of external devices.
● Digital inputs read or monitor external signals. Generates Service Request Message on selected signal changes.
● RS-485 network capability. Supports multiple units on one RS-485 network.
● Includes sample control, calibration and configuration programs. Complete software package.

Brochure EN

ICS Analog Interface Module 2361A is a compact, RS-232/RS-485 to Analog Interface that provides signals for controlling analog devices over a serial path. The Model 2361A has four floating analog output channels, four differential analog inputs, digital output drivers and digital inputs. The analog values can be scaled to match the physical values of the input signals or of the controlled parameters. The scale factors and all other user set confi guration parameters are saved in Flash memory until changed. The 2361A's serial interface provides the functionality of a GPIB interface with control from any PC's COM port or over a RS-485 network. The ICS Analog Interface Module 2361A accepts both industry standard SCPI commands and easy-to-use short form commands. Typical ICS Analog Interface Module 2361A applications are controlling power supplies, providing analog stimuli or measuring analog signals.

Meer informatie
Art.nr.
2361A
Fabrikant
ICS Electronics
Land van herkomst
Verenigde Staten
Interface Specifications
Provides RS-232 full duplex and RS-485 (RS-422) half duplex asynchronous serial interfaces. Unit automatically responds to the serial interface that receives the command.
RS-232 Interface
Signals AB, BA and BB
Mode Full Duplex
RS-485 (RS-422) Interface
Signals TX/RX pair
Mode Half duplex with or without address detection
Addresses 0 to 15
Termination 220 Ω load resistor and 1 KΩ pullup/pulldown
Common Specifications
Baud Rate 1200 to 38.4 Kbaud
Data Bits 7 or 8
Stop Bits 1 or 2
Parity Odd, Even or None
Command Sets
SCPI and short form commands plus the following 488.2 Common Commands:
*CLS, *ESE, *ESE?, *ESR?, *IDN?, *OPC, *OPC?, *PSC, *PSC?, *RCL, *RST, *SAV, *SRE, *SRE?, *PSC, *PSC?, *RCL, *RST, *SAV, *SRE, *SRE?,
Service Request Message SRM nn LF where nn is the Status Byte value.
Analog Inputs

All parameters are specified at 25 °C. Polarity is jumper selected.

Channels 4
Range 0.1, 1 or 10V
Polarity Unipolar or bipolar
Max. Input 30V max.
Input Impedance 1 MΩ
Isolation 750V
Resolution 1 part in 4096 std
Non-linearity ± 1 bit on 10 V range
FS Error
Unipolar 10V, 1V, 100mV, 5mV, 1mV, 0.5mV
Bipolar 10mV, 2mV, 1mV
Temp Drift 17 PPM/°C
End Point 2x FS error
Read time 8.5 ms max.
Analog Outputs

All parameters are specified at 25 °C. Range is jumper selected.

Channels 2, 3 or 4
Ranges 0 to +10, ±10, ±5 VDC
Output current ±5 mA typ.
Isolation 750 VDC, Ch# 4 is referenced to A/D ground.
Zero
Unipolar 0
Bipolar Mid range
Resolution 1 part in 65.535
Non-linearity ± 4 bits
Zero error
± 8 bits (Unipolar)
± 4 bits (Bipolar)
End Point Error ± 8 bits
Temp Drift
Gain ±15 typ., 40 max. PPM/° C
Unipolar Offset ±25 PPM FSR/° C
Bipolar Zero ±35 PPM FSR/° C
Temperature -10 °C to +55 °C
Output ripple 30 mV P-P, 500 kHz
Update time 8 ms from command terminator.
Digital Lines
Inputs 8 lines with 33 KΩ pullups for TTL/CMOS signals or contact closure to ground.
Logic Levels
Low = 0 ± 0.5 VDC
High = > 2.4 VDC
Query time 10 msec to GPIB response
Outputs 4 darlington driver outputs with diodes to V common input
Logic Levels
On < 0.7 V @ 20 mA
On < 1.2V @ 200 mA
Off = V Com - 0.7 V
V Common 48 VDC maximum
Output delay 3 msec from cmd terminator
Grootte
185.2 x 38.6 x 185.2mm (W x H x D)
Connectors and Headers
Connectors
Analog/Digital 62-pin DC shell
Serial 25-pin DB-25S
Omgeving
Operation Temperature -10° C to +55° C
Storage Temperature -20 °C to +80 °C
Power
+12 +1/-0.3 VDC, 7 VA
Included Accessories
Instruction Manual
Support CD with utility and example programs
Mating 62-pin connector and hood
CE/UL/CSA/VDE approved AC power adapters
ICS Analog Interface Module 2361A aanpassen
Aantal

* Verplichte velden

Uw configuratie
RS-232/RS-485 to Analog Interface
ICS Analog Interface Module 2361A
Overzicht
    Mijn vraag gaat over: ICS Analog Interface Module 2361A
    U bent wellicht ook geïnteresseerd in de volgende producten:
    To Top