ICS 2364 GPIB to Relay Interface Board

Levertijd:

3~4 weken

SKU

2364 OEM Board

Serial to Relay Interface OEM Board

● Multiple relay configurations: 16 low-level SPST relays, 16 hi-power SPST relays or 16 relay drivers. Choose the right contact or relay driver for your application.
● Multiple relay programming modes: individual relays, single or multipole scanning. Flexible relay programming.
● Isolated digital inputs accept contact closures and CMOS/TTL logic levels. Eliminates ground loops.
● IEEE-488.2 compatible unit uses SCPI commands. Meets the latest GPIB specifications.
● Includes a menu-driven configuration program. Steps user thrugh configuration choices.
● Metal case provides full EMI/RFI protection. Proven EMI/RFI Compliance.

Brochure EN

Details

ICS 2364 GPIB to Relay Interface Board is available as a Serial to Relay card with 16 SPST relay contacts or as a Serial Relay Driver card with 16 relay driver outputs. Both versions have 8 isolated digital inputs. Choice of low level or heavy duty relay contacts. RS-232 and RS-485 serial interface on a 10 pin header for easy connection.

SPECIFICATIES

Meer informatie

Art.nr.

2364 OEM Board

Fabrikant

ICS Electronics

Land van herkomst

Verenigde Staten

Interface Specifications

Provides RS-232 and RS-485 (RS-422) asynchronous serial interfaces. Unit responds to the serial interface that receives the command.

RS-232 Interface

Signals	AB, BA and BB
Mode	Full Duplex

RS-485 (RS-422) Signals

Signals	TX/RX pair
Mode	Half duplex with or without address detection
Addresses	0 ~ 15
Termination	220 Ω load resistor and 1 KΩ pullup/pulldown resistors

Common Specifications

Baud Rate	1200 ~ 38.4 Kbaud
Data Bits	7 or 8
Stop Bits	1 or 2
Parity	Odd, Even or None

Command Sets

SCPI and short form commands plus the following IEEE 488.2 Common Commands:

*CLS, *ESE, *ESE?, *ESR, *IDN?, *OPC, *OPC?, *PSC, *PSC?, *RCL, *RST, *SAV, *SRE, *SRE?, *TRG, *TST, and *WAI.

Digital Input

Eight isolated inputs that can be queried and/or monitored for selected bit changes. Detected changes are saved and can be used to generate a Service Request (SRQ).

Data Lines

Input Signals

TTL/CMOS or contact closure to ground

Input Levels

Low = 0±0.5 V @ 2 mA

High=>2.4 V or open 1.5 KΩ to +5 VDC or to user furnished external voltage

External Voltage

5 ~ 32 VDC

Isolation

500 VDC to internal logic with external pullup voltage

Monitoring

1,000 samples/sec.

Relay Contacts

All relay contacts are brought out to individual pins on the relay connector. Guard lines are provided between adjacent relay contacts.

Model Number	2364-11	2364-12
Usage	Lo level	Hi Power
Number of Relays	16
Contact Form	Form A (SPST)
Contact Material	Ruthenium	-
Contact Ratings (Restive Load)	0.5 A	1.0 A
Switching V	200 VDC
Power	10 W	50 W
Breakdown V	300 VAC
Resistance	0.15 Ω	0.2 Ω
Life at 100μA	20 x 10⁶ cycles
Life at 500mA	2 x 10⁶ cycles

Relay/Solenoid Driver Outputs

In -14 version, the relays are omitted and the relay drivers are brought directly out to the connector. Drivers are open collector type with an internal snubber diode. User supplies the external voltage for the diodes.

Model Number	2364-14
Usage	External Relays
Number of Drivers	16
Current	300 mA sink max.
Switching V	48 VDC max.

Scanner-sequence Memory

16 relays x 32 steps

Controls and Indicators

PWR	Indicates power on
RDY	Unit has passed self test
TALK	Unit is addressed to talk
LSTN	Unit is addressed to listen
SRQ	Unit is asserting SRQ
ERR	Unit sensed a command error